Why My Bissell Carpet Cleaner Not Spraying – How to Fix

Even the most well-known brands, like Bissell Carpet Cleaner, occasionally experience issues with the spray hose. You may occasionally struggle with the cleaner not spraying any water. Fortunately, the spraying problem is typically not too serious. By examining the state of the tank and the spray tip, the majority of users can fairly easily avoid these issues.

If you are confident that the tank has no significant hardware problems, you can quickly fix the system. In light of this, there is no reason to be concerned. Simply carry out the procedures outlined in this troubleshooting guide.

7 possible reasons why Bissell carpet cleaner not spraying:

• The pump belt is worn, harmed, or missing.
• It is not properly fastened, the red gasket under the formula tank.
• The inline filter is jammed or blocked.
• There is clogging in the spray tips.
• The trigger button is broken (and untethered).
• The product is past its prime.
• The valve beneath the water tank is not properly depressed.

How to Fix Bissell Carpet Cleaner Not Spraying

Refill Tank

With the Bissell carpet cleaner, you should fill the tank up first because an empty tank is typically the cause of this problem. Therefore, even if the outer bladder appears to be filled with unkempt water, be sure to top it off with freshwater or a solution.

If you treat the cleaner well, that should help you prevent the spraying problems. At this point, ideally, the issue will be resolved, preventing the need for further investigation.

Re-seat Water Tank

If you recently purchased the appliance, the water tank’s placement will be the cause of the Bissell cleaner’s problem. To ensure that your tank is properly assembled, check the situation with both latches. Simply remove the tank from its seat and reposition it properly if the latches appear to be in good condition.

Make sure that pulling on the handle will not allow you to pick up the tank. If, however, the tank comes off when you pull it up, it was not seated correctly. To identify the cause of the Bissell carpet cleaner’s malfunction, try reading through the manual one more time.

Check the Condition of the Water Tank

The next thing you should check with the Bissell carpet cleaner is the state of the water tank. You probably can’t spray any solution through the device if the tank is damaged, which is the most likely explanation.

Unfortunately, if your tank is damaged, you don’t have many choices. Check the tank’s condition once more to identify the problem with your unit. In the event that the Bissell carpet cleaner stops spraying, hopefully you won’t have to bother with any additional problems.

Fix the Placement of the Pump Belt

The location of the pump belt can also have a significant impact on this problem. To pinpoint the issue with the Bissell carpet cleaner, you must adjust where the pump belt is located. Simply readjust the belt and then screw everything back into place if the pump belt placement is the true source of the problem to avoid further damage.

The machine’s bottom allows access to the pump belt. The device needs to be completely turned off before being turned upside down with the brushing side facing up. The cover can then be removed by simply removing the screws from the access door. Using the Bissell carpet cleaner, you ought to be able to handle the pump belt issue at this point.

Replace the Pump Belt

Additionally, the pump belt might be broken, in which case you should change it to pinpoint the problem. If the belt is improperly attached to the motor, you won’t be able to spray any water. If your machine requires a working belt, you must contact the dealer to order one. You must install a new piece in order to isolate this belt problem, and the replacement is typically quite affordable.

Clean Spray Tip

If you’re lucky, the problem might only be a clogged spray tip, in which case you just need to remove the tool to get to the sprayer tip. The spray tip can be cleared of debris with any small pin, and doing so won’t take more than a few minutes.

Check the spray tip’s condition and clean it up a little as a result. Hopefully, that will be sufficient to improve the solution’s flow through the tool, and you won’t have to worry about further problems with the Bissell cleaner ceasing to spray water.

Check the Condition of the Water Hose

The amount of water that can pass through the device may also be hampered by a damaged hose. When water leaks out of the hose, you won’t be able to get any water through the hose. So, when you try to use the spray feature after filling the tank, be sure to check for leaks. If water is not spraying through the tool but you can still see leaks on the carpet, you are probably dealing with a similar issue.

To fix the water flow, you will either need to replace the tool or the hose assembly, depending on the damaged sections. When resolving these issues, be sure to obtain compatible replacements from the authorized support personnel.

Get Help from Official Support

You ought to be able to pinpoint the precise nature of the machine’s problem at this point. Calling customer service might be the only option, though, if you’re less fortunate and the problem with your unit persists. Getting a replacement will help you deal with these problems since you can’t do much about a damaged unit. So, if there is a problem, try calling the business or your local Bissell dealer.

You won’t have to worry about wasting hours trying to fix the problem because the problem is usually with an empty tank. Therefore, be sure to first check the tank before tackling the pump belt or the hose connection.

Final Words

The solution to the issue of why my Bissell carpet cleaner isn’t spraying water is there, complete with troubleshooting steps. We are confident that by following our comprehensive troubleshooting guide, your cherished carpet cleaner will be able to spray water and once more clean your home.

FAQs