Loss of suction with your Shark Navigator vacuum? Does it have a terrible odor? One of the primary causes of these issues is that we occasionally forget to clean the shark navigator vacuum. All your shark navigator vacuum needs is regular maintenance to last longer. With the help of our detailed instructions, you can thoroughly clean your shark vacuum and get it back to working like new.
Importance of Cleaning Shark Navigator Vacuum Filter
Cleaning the filter of the vacuum cleaner according to the instructions will help to maintain the suction of the vacuum cleaner for a long time, so that the best cleaning effect can be obtained every time. All filters attached to shark vacuum cleaners, including HEPA filters on the models containing them, can be cleaned or cleaned for reuse.
Read More: Shark Navigator NV352 Upright Vacuum Review 2022
Basic Steps for Cleaning the Shark Navigator Vacuum
Whether you buy shark navigator vacuum or other brands, when using a vacuum cleaner, removing dirt and debris from the equipment should be part of your daily maintenance.
- Disconnect the shark cleaner from the power socket.
- Take out and empty the dust collecting cup and wipe it clean with a dry cloth.
- Remove the handle of the vacuum cleaner and check whether each part is blocked.
- Clean the filter, brush rollers and bristles and allow the air to dry for up to 24
Hours.
- Use a wire hanger or stick to unblock the hose.
- Reassemble your vacuum cleaner.
Tools of Cleaning Shark Navigator Vacuum
- Equipment / tools
- Sink or bowl
- Microfiber cloth
- Clothes hanger
- Soft wool nylon brush
- Dustbin
- Stripper or small scissors
- Material Science
- Cold and warm water
How to Clean the Shark Navigator Vacuum?
- Unplug the power supply
Before cleaning the shark vacuum cleaner, please unplug the power cord from the power socket or remove the vacuum cleaner from the charging station.
Unplug the shark vacuum cable from the power socket
- Check and clean the roller brush
Roller brush or mixing bar is an important part of vacuum cleaner, which can help remove dirt and dust on carpets and floors. If the rotation is blocked by threads or messy hair, the vacuum will not work properly. Use small scissors (manicure) or a seamer to cut the tangled material. Check whether the drum rotates freely.
Scissors cut tangled hair in shark vacuum roller brush
- Clean the dust collecting cup or dustbin
Remove the dust collecting cup or dustbin from the vacuum. Pour the contents into the trash can. Wash the garbage can with warm water, and then wipe the inside and outside of the container with microfiber cloth or sponge. If possible, open the top and bottom hinges and allow the dustbin to dry.
- Check the hose
After removing the trash can, disconnect the hose and check for any blockage. Move the hose down and check it for cracks or holes that may weaken the vacuum suction. Disconnect the hose near the head of the vacuum cleaner and remove any obstacles there. If you find clogs, please use a standard ruler or garden hose to remove debris. Work slowly and carefully to avoid puncturing the hose.
Read More: How to Clean A Vacuum Hose
- Wipe the hose with a wet microfiber cloth and reconnect it correctly.
- Check the shark vacuum hose for cracks or lumps
- Clean the filter and screen
Find the filter and dust net. To clean the foam and / or felt filter, rinse it with cold water only. Do not use any soap or cleaning products that may damage the filter. Gently squeeze the filter with your fingers to remove dirt. Continue to change the water until it is no longer muddy. Roll the filter with a microfiber towel to remove excess water. Do not twist.
For foldable filters, if debris is attached to the filter, gently brush off the dust with a soft bristled nylon brush (old toothbrush). To clean, place the filter in the plastic housing under the cold water faucet until the water is clear.
Put the filters on the drying rack, let them dry for at least 24 hours, and then reinstall them to prevent the liquid from being sucked into any electronic components.
- Wash the shark vacuum filter under flowing cold water
You can use a moist microfiber cloth to wipe the shell of the vacuum cleaner. Pay special attention to any ventilation holes near the motor and remove excess dust.
Wipe the shell of shark vacuum cleaner with wet microfiber cloth
- Check wires
If you have a wired shark vacuum cleaner, please check the wires for any cracks or exposed wires. If you see them, it’s time to repair them.
FAQs of Cleaning Shark Navigator Vacuum
- How to check blockage in shark navigator vacuum?
You can check whether the floor head, rod, hose and airway of shark navigator vacuum are blocked. If you have a vertical vacuum cleaner, first remove the handle and check whether there is suction after opening it – if not, there may be obstacles in the handle or hose. If this part is clear, or if you have a vacuum cleaner, please check the dust suction stick to ensure that nothing is stuck in the pipe. You can also shine a flashlight into the hose. Finally, check whether the arm at the head of the floor – where you connect the Wand – is blocked.
- How often should I clean the shark navigator vacuum?
No matter what type of vacuum cleaner you have, you should clean it regularly. You can empty the dust collecting cup or dustbin after each use or when it is about half full to help maintain suction. We should check whether the rollers and hoses of shark navigator vacuum are tangled, blocked or broken every month, and wipe the shell to remove dust. In the instruction manual of shark navigator vacuum, specific information about the best method to clean and maintain the filter will be provided. The user manual of shark navigator vacuum recommends cleaning the pre motor filter every three months and the post motor filter every year. According to the user manual, you should clean the shark navigator vacuum filter every three months. HEPA (high efficiency particulate air) filter can operate for two years without failure. However, if you find that its efficiency is declining, you may need to clean or replace it as soon as possible. Essentially, you need to remember to clean your shark vacuum cleaner four times a year to make it work properly.
If you lose or throw away the operation manual of shark vacuum cleaner, you can visit shark clean Com online to find instructions suitable for your specific model. You will find information about the location of the filters, how to clean them, and the recommended cleaning frequency.
Read More: How Often Should You Vacuum?
- How to clean the filter of shark navigator vacuum?
After removing the dirt can from the larger dust collection assembly, you will find the filter. Depending on your shark vacuum model, the filter may be made of foam rubber. Additional filters can be made of felt.
You can immerse the foam filter in soapy water and wash it thoroughly. Even after a good scrubbing, the filter may look dirty. The important thing to remember is that they are clean.
Shark does not recommend cleaning felt filters because they are easily damaged. Therefore, tap them gently to loosen the dirt and wipe them clean.
If you choose to wash them, please immerse them in soapy water, just like their foam counterparts. However, please wash them gently. Remember, you will take your own risk.
You can rinse the soap off the filter, place them flat and let them dry for at least 24 hours. If the filters are worn, this may indicate that this is a good time to replace them. Be sure to purchase filters that are specific to your model.
Read More: How to Clean a Vacuum Filter
- How to clean the brush head of shark navigator vacuum?
The rotating brush bears the brunt of cleaning, and you will find debris on it, such as hair, string and other dirt. To clean your rotary brush, first you need to separate the floor attachment from its handle. Most models of floor accessories have a button at both ends. Press these buttons to release the brush head for better cleaning.
You can use scissors to cut the debris wrapped in the brush. Then gently pull out all debris by hand, taking care not to damage the bristles in the process. You can use a soft brush to remove stubborn dirt or immerse the brush in water and scrub thoroughly. Allow the brush to dry for at least 24 hours before reconnecting.
You should also check the hose for obstructions that may hinder movement. Remove the hose from both ends. Carefully check the end and the entire length of the hose. If the vacuum hose is blocked, please put it on the hot water tap and run it. Close one end of the hose by hand, remove the hose from the faucet, and close the other end. Shake the hose well. Next, you can mix baking soda and vinegar in a pot and pour them into a hose. Like hot water, you need to cover one end with your hand, and the other end also needs to be covered. Shake well for a few minutes.
Release the mixture and let warm water pass through the hose, then cold water. The mixture of baking soda and vinegar helps to dredge the hose and remove unpleasant smells. In addition, hot water helps loosen and remove dirt. Then you need to lay the hose flat and dry it. After completely drying, reconnect it to the equipment.
You can check the opening for any blockage after removing the hose from the connector. Turn the floor nozzle upside down. Tap it gently to loosen any dirt, and then remove it with an old toothbrush.
Conclusion
The lower pipe hose connected to the electric floor nozzle is a small hose, which is often forgotten in the process of cleaning the shark navigator vacuum. We need to remove it and check for blockage. Also check the opening for obstructions. Clean it in the same way as the main hose and brush off each opening as shown above. After cleaning the shark navigator vacuum, we need to reassemble all parts, carefully ensure that each part is completely dry, and thoroughly wipe the whole vacuum cleaner in order to ensure that the outside is as clean as the inside.
